|
|
ValvesThe V1FS and V2FS butterfly valves are a necessary equipment for the discharge of bins which contain powder products. External body is made from cast aluminium (alloy), disk made from cast iron or plastic coated and seal made from neoprene. The V2FS valves are equipped with a top and bottom flange whereas the V1FS has a top flange only.
Key Features:
• Suitable for the food industry.
• Dust proof.
• Cast iron Butterfly.
• Pressure proof up to 0,2 bar.
Drives :
The valves can be equipped with manual, electropneumatic and gear motor drive. The drive units are completely interchangeable.
Sizes Avalible :
V1FS 100 - 100mm dia V1FS 150 - 150mm dia
V1FS 200 - 200mm dia
V1FS 250 - 250mm dia
V1FS 300 - 300mm dia
V1FS 350 - 350mm dia
V1FS 400 - 400mm dia
V2FS 100 - 100mm dia
V2FS 150 - 150mm dia
V2FS 200 - 200mm dia
V2FS 250 - 250mm dia
V2FS 300 - 300mm dia
V2FS 350 - 350mm dia
V2FS 400 - 400mm dia
Square Slide ValvesThree interchangeable drives for the same valve body, hand wheel, pneumatic drive, gear motor drive.
Key Features
• Painting: RAL 7001
• Valve body entirely coated with SINTEX (SINTAL) in order to avoid direct contact between the product and the valve body.
• Heavy Duty Blade
• Friction - Free Contact
• No Additional Lateral Seals
• Dry Food Quality (Coated in SINTAL)
• Dustproof
• Waterproof (on Request)
• Simple and economic due to a low number of components.
• Wide clearance, no friction possible.
• No additional lateral seals required.
Sizes Avalible
VLQ0200 - 200mm square
VLQ0250 - 250mm square
VLQ0300 - 300mm square
VLQ0350 - 350mm square
VLQ0400 - 400mm square
or Stainless Steel 304
Round Slide Valves
Three interchangeable drives for the same valve body, hand wheel, pneumatic drive, gear motor drive.
Key Features
• Painting : RAL 7001
• Valve body entirely coated with SINTEX (SINTAL) in order to avoid direct contact between the product and the valve body.
• Heavy Duty Blade
• Friction - Free Contact
• No Additional Lateral Seals
• Dry Food Quality (Coated in SINTAL)
• Dustproof
• Waterproof (on Request)
• Simple and economic due to a low number of components.
• Wide clearance, no friction possible.
• No additional lateral seals required.
Sizes Avalible
VLC0200 - 200mm dia
VLC0250 - 250mm dia
VLC0300 - 300mm dia
VLC0350 - 350mm dia
VLC0400 - 400mm dia
or Stainless Steel 304
Rotary Valves
Rotary valves are ideally suited to control delivery or discharge of powder or palletised products to and from silos, hoppers, pneumatic transport systems, bag filters and centrifugal separators.
Its strong and compact construction, thanks to the original design, makes it a simple matter to access the internal working parts. Four different types are available according to the different flow rates.
The following theoretical diagram provides some general guidelines on the type of valve to be used. Bear in mind, however, that the type of material discharged and the rotational speed. Three standard speeds are available: 10/20/30 rpm. In addition, the range will include a range variator from 4 to 22 rpm.
SIZING - Given the variety of types, specific diagrams for every material have not been prepared. However here is some essential data to
make a correct choice easier.
The box load for powder or similar material is more or less 80% of the theoretical value and optimum levels can be obtained with valve rotation at 20 rpm.
Low valve rotation means low wear level, thus if you are working with abrasive materials, it is better to use large capacity valves which run at
low speed.
The construction material depends on the type of material to handle. There are three basic types:
Non contaminating materials:
Body - grey cast iron
Covers - cast iron
Rotor - cast iron or steel
Abrasive products:
Body - chromium or nickel plated cast iron
Covers - chromium or nickel plated cast iron
Rotor - steel or cast iron with Vulkolan scrapers
Corrosive products:
Body - chromium or nickel plated cast iron
Covers - chromium or nickel plated cast iron
Rotor - stainless steel
Pinch Valves
The pinch valve, type VM, was designed to be used in a wide range of applications. Their primary use is to arrest the flow of product in the pneumatic conveying line, for material such as powders, granules, fibers and liquids. The wide range of sleeve materials along with various body types make the valve suitable in various industries.
Advantages:
• Free passage, full bore through no pressure loss.
• No product/metal body contact.
• No maintenance.
• Low weight.
• Low air consumption.
• Suitable for plants requiring explosion proof line closure.
TECHNICAL CHARACTERISTICS:
Flanges: PN10 standard.
SIZES AVALIBLE :
VM13 - 13mm bore
VM20 - 20mm bore
VM25 - 25mm bore
VM32 - 32mm bore
VM40 - 40mm bore
VM50 - 50mm bore
VM65 - 65mm bore
VM80 - 80mm bore
VM100 - 100mm bore
VM125 - 125mm bore
VM150 - 150mm bore
VM200 - 200mm bore
BODY :
Aluminium
Carbon steel
Stainless steel 304
Stainless steel 316
SLEEVE MATERIALS:
Natural rubber
Polythene resin
NBR (food quality)
Neoprene
Silicone
Hypalon
Viton
EPDM
Nitrile (cyanocarbon)
Operating Pressure: max. 6 bar.
Control Pressure: max. 8 bar.
Differential Pressure: Max 1.5 to 2 bar depending on sleeve construction.
Pressure Relief Valve
APPLICATION :
On top of silos and bins, hoppers, containers to avoid overpressure and underpressure. To avoid problems which could severely damage both silo
and filter.
MATERIALS :
All contact parts are in mild steel, on request in stainless steel. Cover is made from polymer, seals according to application.
For a correct operation the application of a pressure relief valve is necessary in order to discharge possible over pressure inside the silo, as well as
negative pressure. In fact there is pressure once you fill the silo and negative pressure when you empty the silo. If air input and output are not
correct the valve opens (one way or the other) and avoids possible silo damage.
Please contact us so we can analyze your valve needs.